Fiber

A More Advanced Type of Wear Tester has been Realized
In this instrument, for a single measurement of test paper strip, it is possible to create 3-dimensional wear condition graphs showing the relationships between the number of wear movements, vertical loading, friction and wear volumes, and to determine the critical loading responding to wear transitions. Accordingly, not only will it be unnecessary to have multiple test pieces, but the testing time will also be greatly shortened and the requirement for troublesome data analysis can be eliminated, allowing excellent data to be obtained.

Expressing Sensory Evaluation in Numerical Values
This instrument allows texture, feeling, and blending, which were previously difficult to quantify, to be shown numerically.
Using three strain gages, the resistances in the X, Y and Z directions is detected.
Operation only requires placing the sample on the test piece table and tracing the object with your finger or other object. Measurement can be easily carried out.
In addition, using the handy probe, samples that can not be loaded on the test piece table can also be measured.

Standard model of new friction and wear tester
Hop-up type acrylic cover that can be covered during measurement, newly developed orthogonal balance arm method, etc.
The birth of a new generation standard model of Tribo Gear.
Equipped with a Y-direction stage as standard, making testing easier.
Perform friction and wear tests comfortably with the Tribo Gear TYPE 40, which is easier to use and more accurate.

Measurements by Anyone, Anywhere
The Muse Type: 94i-IIis a portable measuring instrument that can easily be used by anyone to measure the static friction coefficient between objects.
Previously, methods of measuring static friction generally used incline methods and strain gages, and their use was limited to locations such as laboratories. The inability to make measurements on-site was a weak point of these methods.
This unique instrument is offered as a “new static friction measurement method” that solves all of the above problems at once.

Supports a Variety of Research Topics
A DC servo motor (FW type) permits a linear movement of the mobile base when loaded with a test piece.
The resistance transmission mechanism, consisting of the vertical arm and horizontal arm with two fulcrums, conveys the resistance received from each adapter to the detector of the load converter.
A zero balancer is provided at one end of the horizontal arm to balance the dead weight of each adapter so that the vertical loading becomes zero.
In addition, at the other end of the arm there is an adaptor holder, and directly above this there is a weight pan on which weights up to 1000g can be applied.
The detected resistance is amplified by the dynamic strain amplifier and can be output to each recorder.
An easy to use touch panel has been utilized in the operation and display units.

Measurements by Anyone, Anywhere
The Muse Type: 94i-IIis a portable measuring instrument that can easily be used by anyone to measure the static friction coefficient between objects.
Previously, methods of measuring static friction generally used incline methods and strain gages, and their use was limited to locations such as laboratories. The inability to make measurements on-site was a weak point of these methods.
This unique instrument is offered as a “new static friction measurement method” that solves all of the above problems at once.

Easy Static Friction Coefficient Measurement Allows Use as a Research, Inspection and Teaching Aid
The test piece is installed on the ascending board and flat indenter. The ascending board is provided with a sensor that monitors the movement of the flat indenter.
The ascending board starts from the horizontal position, and the tilt increases when the measurement begins. The sensor detects the motion when the flat indenter begins to slide, and instantly stops the ascending board.
The angle and tan?? at this time should be read.

Use for Peeling and Tensile Strength Evaluations
The test piece clamps on both sides move at the same speed in opposite directions, and the resistance is accurately measured at one of the clamps.
An empty part is prepared between both clamps into which the unpeeled sample is inserted.
Accordingly, the T-type Peeling

Birth of a high-performance, low-cost friction and wear tester.
We have reduced costs as much as possible while maintaining the measurement performance of friction gears.
The basic performance is comparable to high-end models such as touch panel operation and various measurement ranges.
A load converter with an integrated stylus holder has been adopted to further improve operability.
Tribosoft (optional) makes it easy to measure, analyze, and manage from measuring the coefficient of static friction to measuring reciprocating wear.